The Increase of Silver Grass Ash Melting Temperature Using Additives

Michal Holubcik, Jozef Jandacka, Milan Malcho, Tadeas Ochodek, Jan Kolonicny

Abstract


Some types of biomass have a high content of alkali oxides and salts and, thanks to it they feature a low ash melting temperature which may result in various combustion problems. Slag and sintered particles that are formed prevent the fuel from being supplied, restrict the access of combustion air, heat transfer in the heat exchanger and can cause corrosions. One possibility of increasing the ash melting temperature is to add additives. Some additives can change chemical composition of fuel ash, thus changing also the ash melting temperature. The paper deals with the adding of 2 % additives – kaolin, talc, lime, limestone, dolomite, bentonite to silver grass. The tested additives increased the ash content but they also changed its chemical composition, which resulted in the increase of the ash melting temperature. Best positive results were achieved with kaolin and lime which increased the ash melting temperature by approx. 300 °C.

Keywords


biomass, silver grass, additives, ash melting temperature, chemical composition of ash, ash content

Full Text:

PDF

References


Soos, L., Kolejak, M., Urban, F. (2012): Biomass - Renewable Energy Source (in Slovak), Vert: Bratislava

Holubcik, M., Jachniak, E., Smatanová, H. (2014): Differences between pellets from biomass made in manufactory and in domestic conditions, AIP Conference Proceedings, 1608, pp. 48-53

Dobrowolska, E., Dzurenda, L., Jablonski,M., Klosinska, T. (2010): Energy using of dendromass. Wydawnictwo SGGW, Warszawa, 168 p.

Holubcik, M. (2013): Possibilities of Increasing Ash Melting Temperature from Biomass (in Slovak), PhD thesis, University of Zilina

Buczynski, R., Weber, R., Szlek, A., Nosek, R. (2012): Time-dependent Combustion of Solid Fuels in a Fixed-bed: Measurements and Mathematical Modeling, Energy and Fuels, vol. 26, pp. 4767-4774

Vassilev, S., Baxter, D., Andersen, L., Vassileva, C. (2010): An overview of the chemical composition of biomass, Fuel, Vol. 89, pp. 913 – 933

Nosek, R., HolubÄík, M., PapuÄík, Å . (2014): Emission controls using different temperatures of combustion air, The Scientific World Journal, Hindawi Publishing Corporation, Vol. art. No. 487549

Zhongxin, T. , Lagerkvist, A. (2011): Phosphorus recovery from the biomass ash: A review, Renewable and Sustainable Energy Reviews, Vol. 15

Cernecky, J., Neupauerova, A., Janosko, I., Soldan, M. (2010): Environmental Technology (in Slovak), Technicka univerzita: Zvolen, 274 p.

Vitazek, I., Vitazkova, B., Ploth, J. (2013): Production of Gas Emissions from Biomass heat Source. Engineering Mechanics, vol. 20, No. 3/4, pp. 289-298.

Nosek R., HolubÄík M. (2013): Measurement of particulate matter during the combustion of phytomass in small heat sources, Power control and optimization: proceeding of seventh global conference: Yangon, Myanmar

Bostrom, D. (2008): Slagging Characteristics during Combustion of Corn Stovers with and without Kaolin and Calcite. Energy and Fuels, vol. 22, pp. 3465-3470.

Pedersen, R. S. (2003): Residual ash formation during combustion of woody biomass. Copenhagen: Department of Chemical Engineering, Technical University of Denmark

Nosek R., HolubÄík M., Suľovcová, K. (2013): Measurement of emissions during combustion of phytomass in small heat sources (in Slovak), 32. stretnutie katedier mechaniky tekutín a termomechaniky, Žilina: Žilinská univerzita, pp. 205-208

Liorente, M. J. F., García, J. E. C. (2005): Comparing methods for predicting the sintering of biomass ash in combustion, Fuel, vol. 84, pp. 1893 – 1900

Toscano, G., Corinaldesi, F. (2010): Ash fusibility characteristics of some biomass feedstock and examination of the effects of inorganic additives, Journal of Agricultural Engineering, Vol. 41 No. 2, pp. 13-19

Suri, A., Horio, M. (2010): Solid biomass combustion. Handbook of Combustion: Solid Fuels, Weinheim

Werkelin, J., Skrifvars, B., Hupa, M. (2005): Ash - forming elements in four Scandinavian wood species, Biomass and Bioenergy, vol. 29, issue 6, pp. 451–466

Pedersen, R. S. (2003): Residual ash formation during combustion of woody biomass. Copenhagen: Department of Chemical Engineering, Technical University of Denmark

Zevenhoven M.(2001): Ash-forming matter in biomass fuels. Ãbo/Turku: Faculty of Chemical Engineering, Ãbo Akademi University, 88 p.

Zevenhoven M. (2003): Co-Firing in FBC a challenge for fuel characterization and modeling. Proceedings of the international (ASME) conference on fluidized bed combustion

Dzurenda, L., Slovák, J. (2001): Energy properties of pellets made from spruce sawdust. In: Acta Mechanica Slovaca. Vol. 5(3), pp. 201 - 206.

Taus, P., Tausova, M. (2009) Economic Analysis of FV Power Plants According to Installed Performance, Acta Montanistica Slovaca, Vol. 14, No. 1

STN EN 14775, 2009: Solid biofuels. Determination of ash content

STN ISO 540, 2008: Hard coal and coke -- Determination of ash fusibility




DOI (PDF): https://doi.org/10.20508/ijrer.v5i1.1981.g6493

Refbacks

  • There are currently no refbacks.


Online ISSN: 1309-0127

Publisher: Gazi University

IJRER is indexed in EI Compendex, SCOPUS, EBSCO, WEB of SCIENCE (Clarivate Analytics)and CrossRef.

IJRER has been indexed in Emerging Sources Citation Index from 2016 in web of science.

WEB of SCIENCE in 2025; 

h=35,

Average citation per item=6.59

Last three Years Impact Factor=(1947+1753+1586)/(146+201+78)=5286/425=12.43

Category Quartile:Q4